Translation of "offloading conveyor" to Thai language:


  Examples (External sources, not reviewed)

They call it the ocean conveyor.
ม นถ กเร ยกว าสายพานลำเล ยงแห งมหาสม ทร
it's like I'm on a conveyor belt.
เขาทำเหม อนว าฉ นน ะเป นพวกก อสร างน ะ
I put the shoe on the conveyor belt.
ผมเป นคนวางรองเท า บนสายพานเอง
You can operate the chip conveyor in Setup mode but you must press and hold the conveyor key CHlP FWD
ค ณสามารถใช ลำเล ยงช ปในโหมดการต ดต ง แต ค ณต อง กดแป นลำเล ยง ฟอร เว ร ดช ป ค างไว
Connect the Electrical Cable to the receptacle labeled Conveyor
เช อมต อสายเคเบ ลไฟฟ าเพ อรองร บการต ดป ายว า เคร อง
Ask someone to assist you to hold the weight of the Chip Conveyor while you unfasten the Shipping Security Screws and lower the Conveyor into position
ขอให คนช วยจ บน ำหน กของเคร องช ในขณะท unfasten จ ดส งความปลอดภ ย Screws และด านล างเคร องท ลงในตำแหน ง
Route the Electrical Cable neatly from the Conveyor Motor down to the receptacle
เส นทางสายไฟฟ าบรรจงจากเคร องมอเตอร เพ อรองร บการ
If a Chip Guide Bracket is included with the Conveyor Accessories, install it now
ถ าวงเล บแนะนำช ปท ม อย ในอ ปกรณ เคร อง ต ดต งน นขณะน
Move to the Belt Tensioning Bolts and tighten them inwards towards the Conveyor Motor
ย ายไปในแถบ Tensioning สาย และตร งตรา inwards ไปย งเคร องมอเตอร
With electricity supplied to the Conveyor press the CHlP FWD key to make sure the Conveyor Belt feeds smoothly with no binding or dragging inside the Enclosure and at the Chip Discharge Point
ม ไฟฟ ามาท เคร อง กดป ม FWD ช เพ อให แน ใจว า สายพานต วด งข อม ลได อย างราบร น ไม ผ กหร อลากภาย ในการป ดล อม และจ ดปลดช
Connect both coolant pump power cables as well as the power cable for the chip conveyor
การเช อมต อท ง coolant ป มไฟเป นสายไฟสำหร บ conveyor ช
Once installed push the Conveyor back in towards the center of the Machine until it is fully seated
เม อต ดต งกดท เคร องสำรองในส ศ นย กลางของเคร องจ กรจนกว า ม นจะเต มน ง
With the conveyor lowered install the Bracket Screws back into the holes they came from on the Enclosure Side Panel
ด วยเคร องลดลง ต ดต ง Screws เล บลงไปในหล มพวกเขามาจากบนแผงด านข างเล า
Note that any chip conveyor support screws or brackets should not be touching the ground until after the leveling procedure is complete
หมายเหต ว า ช เคร องสน บสน น screws หร อวงเล บใด ๆ ไม ควร ได ส มผ สพ นด นจนกระท งหล งจากเสร จส นกระบวนการ leveling
Start with the screws on the chip conveyor side followed by two of the four screws on the left side of the panel
เร มต น ด วย screws ด าน conveyor ช ตาม ด วยสอง screws ส บนแผงด านซ าย
Remove the four Screws connecting the Conveyor Shipping Brackets to the Machine Enclosure and carefully lower the section until it is set in the installed position
เอา Screws ส ท เช อมต อเคร องส งวงเล บป ดล อมเคร องจ กร และค อย ๆ ลดส วนจนม การต งค าในตำแหน งท ต ดต ง

 

Related searches: Offloading Conveyor - Ssl Offloading - Offloading Data - Loading And Offloading - Floating Production Storage And Offloading Unit - Offloading Facilities - Floating Production Storage Offloading Vessel - C3 Offloading - Floating Production Storage Offloading Vessels Fpso - Offloading Devices -